Free Shipping

2500W ZVS Induction Heating Board Module Flyback Driver Heater+Tesla Coil+Dual fan


To confirm that this part fits your vehicle, please enter your vehicle's details below.

  • Year:


    • Make:


      • Model:


        • Submodel:


          • Trim:


            • Engine:


              • Clear All
              This part is compatible with 0 vehicle(s).
              Show all compatible vehicles
              This part is compatible with 1 vehicle(s) matching
              This part is not compatible with
              Recent searches

                • Year
                • Make
                • Model
                • Submodel
                • Trim
                • Engine

                  Name: 2500W ZVS Induction Heating Board Module Flyback Driver Heater+Tesla Coil+Dual fan

                  If you need suitable DC power supply for this product , recommend ID:1611455

                  Product Description
                  Material: metal + plastic
                  Color: Black
                  Power supply:
                  New style :AC 100-220V Adapter
                  Old  style: Mainboard Input voltage: 12V-48 recommended above 36V
                  Power requirements: less than 12V ≥ 10A 15V or more ≥ 20A
                  NOTE:New style and Old  style shipped  by randomly!!!
                  It doesn‘t affect the performance of product.!!!
                  Maximum power: 2500W
                  Maximum current: 50A
                  Size: 25x12x9cm (Manual measurement, error about 3mm, please understand)
                  ●The heating plate is made of military-grade PCB, and the performance is stable;
                  ●The power line is fully covered with copper cover design, which can increase the current and heat generation;
                  ●Using oversized and large power heat sink to dissipate heat better;
                  ●The output terminal uses three M4 copper columns in parallel, which can be connected to other outputs such as high voltage package;
                  ●Using six IRFP260 and 12 capacitors in parallel resonance, the power is high and the efficiency is high;
                  [Buyers must see / pay special attention]
                  The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. The buyer can prepare water cooling system separately, can buy a small water pump and 2 meters of inner diameter Of 4mm rubber hose.
                  2. You must pay attention to when using switch power supply, because the high-power switching power supply usually have soft start function, the same output voltage is slowly rising, and if the voltage rise to 10V before By lacking voltage lead to circuit can't afford to vibrate, so that the two MOS tube conduction and burned components at the same time, so be sure to switch the power supply voltage stability and then access the induction heating circuit.
                  3. When heating the metal objects do not to heat too large metal, otherwise it may be overloaded with power, please add a 35A fuse or ammeter and air switch will be better. (package does not inclues)
                  4. Although this drive plate can withstand more than 40A current, but it is recommended that not exceed 48V 35A to prevent accidents and damage.
                  5. Package comes with heating circle diameter is 60 mm, design voltage is 36V, if you use more than 40 voltage power supply shall be used for inner diameter 70 mm above diameter heating ring, water pump use 12V dc power supply, please use separate Power supply voltage regulator module to avoid burn out fan and water pump.
                  6. The minimum input voltage of the module is 12V, it doesn't mean all the 12V power supply can be used, some novice buyers may use a smaller power supply. This module has specific voltage and current requirements, the voltage 12V current must Be more than 10A power supply can be used, if the power is too low will lead to the power output is greatly reduced, when the voltage is lower than 12V, it will lead to two MOS at the same time conduction, will burn MOS tube ;
                  7. If you find that the MOS tube fever, then the first thing to consider whether the power output meets the requirements.
                  8. Do not empty the board, otherwise it will issue a very high frequency of noise, and then MOS tube will burn out.
                  9. Induction heating is recommended to use 36V 20A power supply, 12V power supply is too small heating almost no response, and 12V power supply easily lead to the power supply output voltage decreases, below 12V is very dangerous
                  10. Induction heating power is great, so fever is normal, be sure to do a good job of cooling.Induction heating, the power recommended more than 48V 50A switching power supply. More than 24V power supply, then more than 20A power supply, the greater the voltage, the greater the current, the greater the heating power, heating faster.
                  Application: high frequency induction heating plate
                  How to use? (Instructions)
                  For induction heating, it is recommended to use a switching power supply of 48V50A or higher. If the power supply is 24V or more, a power supply of 20A or more is required. The higher the voltage, the larger the current, the higher the heating power, the faster the heating speed.
                  Package include:
                  ● 1 x PCB board (with dual fans)
                  ●1 x 48V copper tube

                  Leave a Comment