Price:
US$57.99
Compatibility
To confirm that this part fits your vehicle, please enter your vehicle's details below.
-
Year:
Select
-
Make:
Select
-
Model:
Select
-
Submodel:
Select
-
Trim:
Select
-
Engine:
Select
- Clear All
Show all compatible vehicles
- Year
- Make
- Model
- Submodel
- Trim
- Engine
-
<!–
- Products Name: Eachine Cinfun Spare Part CRAZYBEEX FR V2.2 F4 OSD 1S Flight Controller AIO 5A ESC 5.8G 40CH 25/200mW VTX and Receiver for Whoop RC Drone FPV Racing
- Brand: Eachine
- Product id: 1824618
–>
<!–
–>
Specification:
Brand Name: Eachine
Model: CRAZYBEEX FR V2.2
Item Name: F4 1S FC AIO ESC VTX & Receiver
Input Voltage: 1S Lipo
Size: 28.5×28.5mm
Mounting Hole: 25.5×25.5mm
Weight: 4.4g
Application: Original Replace Part for Eachine Cinefun 1S FPV Racing Drone
| F4 OSD Flight Controller | (Frsky SPI RX version) CRAZYBEEX FR V2.2 FC Firmware target: CrazybeeF4FR (Flysky SPI RX version) CRAZYBEEX FS V2.2 FC Firmware target: CrazybeeF4FS (External TBS CRSF NANO version) CRAZYBEEX PNP V2.2 Firmware target:CrazybeeF4DX MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1-2S battery input (DC 2.9V-8.7V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI Frsky/Flysky receiver or no receiver Built-in 5V 1A BEC |
| Onboard 5A 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_8.HEX Default protocol: DSHOT600 |
| Onboard 5.8G 40CH 25/200mW VTX |
Output power: 25mw~200mw switchable Input voltage: 3.3V 5.5V Default vtx_power is 3 |
|
Onboard Voltage and Current detector |
Voltage Meter scale: 110 |
|
Onboard Receiver ( Optional) Compatible Frsky Receiver Version |
SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 model |
|
Onboard Receiver ( Optional) Compatible Flysky Receiver Version |
SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m Failsafe support |
CrazybeeX FR V2.2 Bind procedure:
1. Make the on board receiver get into bind mode: Plug USB and then press the bind button for 1 second, the Red LED on the top of the flight controller will getting to be solid , this indicate the receiver is in bind mode;
Or use bind code to bind :For 3.5.7 version firmware Plug USB and then connect Betaflight configurator and then move to CLI tab , type “Frsky_bind”, the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode;
For 4.0.x the bind code is “bind_rx_spi” ,For 4.1.x or 4.2.x the bind code is “bind_rx”
2. Make your Frsky transmitter get into bind mode . If bind is successful the red led will starting to blink.
The red LED wouldn’t blinking when binding with some new ACCESS firmware frsky radio, but the bind is actually successful ,
need to go to CLI command and type “save” to finish the binding .
Package Included:
1x F4 AIO Board
4x Anti-vibration Ball
1x bag of Screws
- Brand: Eachine
- Voltage: 1S
- RC Drone Spare Parts: Flight Controller,ESC
Precise details:
Specification:
Brand Name: Eachine
Model: CRAZYBEEX FR V2.2
Item Name: F4 1S FC AIO ESC VTX & Receiver
Input Voltage: 1S Lipo
Size: 28.5×28.5mm
Mounting Hole: 25.5×25.5mm
Weight: 4.4g
Application: Original Replace Part for Eachine Cinefun 1S FPV Racing Drone
| F4 OSD Flight Controller | (Frsky SPI RX version) CRAZYBEEX FR V2.2 FC Firmware target: CrazybeeF4FR (Flysky SPI RX version) CRAZYBEEX FS V2.2 FC Firmware target: CrazybeeF4FS (External TBS CRSF NANO version) CRAZYBEEX PNP V2.2 Firmware target:CrazybeeF4DX MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1-2S battery input (DC 2.9V-8.7V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI Frsky/Flysky receiver or no receiver Built-in 5V 1A BEC |
| Onboard 5A 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_8.HEX Default protocol: DSHOT600 |
| Onboard 5.8G 40CH 25/200mW VTX |
Output power: 25mw~200mw switchable Input voltage: 3.3V 5.5V Default vtx_power is 3 |
|
Onboard Voltage and Current detector |
Voltage Meter scale: 110 |
|
Onboard Receiver ( Optional) Compatible Frsky Receiver Version |
SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 model |
|
Onboard Receiver ( Optional) Compatible Flysky Receiver Version |
SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m Failsafe support |
CrazybeeX FR V2.2 Bind procedure:
1. Make the on board receiver get into bind mode: Plug USB and then press the bind button for 1 second, the Red LED on the top of the flight controller will getting to be solid , this indicate the receiver is in bind mode;
Or use bind code to bind :For 3.5.7 version firmware Plug USB and then connect Betaflight configurator and then move to CLI tab , type “Frsky_bind”, the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode;
For 4.0.x the bind code is “bind_rx_spi” ,For 4.1.x or 4.2.x the bind code is “bind_rx”
2. Make your Frsky transmitter get into bind mode . If bind is successful the red led will starting to blink.
The red LED wouldn’t blinking when binding with some new ACCESS firmware frsky radio, but the bind is actually successful ,
need to go to CLI command and type “save” to finish the binding .
Package Included:
1x F4 AIO Board
4x Anti-vibration Ball
1x bag of Screws