Free Shipping

Eachine Twig 115mm 3 Inch 2-3S FPV Racing Drone BNF Frsky D8 Crazybee F4 PRO V3.0 Runcam Nano2 / Caddx Baby Turtle HD Cam


To confirm that this part fits your vehicle, please enter your vehicle's details below.

  • Year:


    • Make:


      • Model:


        • Submodel:


          • Trim:


            • Engine:


              • Clear All
              This part is compatible with 0 vehicle(s).
              Show all compatible vehicles
              This part is compatible with 1 vehicle(s) matching
              This part is not compatible with
              Recent searches

                • Year
                • Make
                • Model
                • Submodel
                • Trim
                • Engine

                  Brand Name: Eachine
                  Item Name: 115mm Twig 3 Inch 3S Brushless FPV drone
                  Wheelbase: 115mm
                  Size: 105mm*100mm*45mm(without propellers)
                  Weight: Twig115 60g(without battery)
                                Twig115 HD 72g(without battery)

                  New Crazybee F4 PRO V3.0 AIO Flight controller 2-4s Lipo Compatible
                  Powerful and smoothly
                  Betaflight OSD support ,easy to get RSSI, Voltage ,current from your goggles
                  Camera Angle adjustable
                  VTX power switchable 25mw~200mw
                  Smartaudio ready , change VTX bands, powers, channels via OSD
                  Built-in SPI Frsky D8 receiver
                  Compatible both for 2s-3s Lipo/LIHV
                  Runcam Nano2 version or Caddx Baby Turtle HD version
                  Support to add external SBUS receiver (Frsky XM+ , RXSR) to get better range by reserved receiver wire.

                  Spare parts specifications:

                  Motor Mode: EX1105 KV5200
                  Stator Diamter:11mm
                  Stator Length:5mm
                  Shaft Diameter:Φ1.5mm
                  Motor Dimension(Dia.*Len):Φ14mm*17mm
                  No.of Cells(Lipo):2S-3S
                  Flight controller (Frsky version) CRAZYBEE F4FR PRO V3.0 Firmware target: CrazybeeF4FR
                  MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
                  Sensor: MPU-6000(SPI connection)
                  Board size: 28.5 * 28.5MM
                  Power supply: 2-4S battery input (DC 7-17V)
                  Built-in 10A(each) Blheli_S 4in1 ESC Dshot600 ready
                  Frsky version Built-in SPI Frsky receiver with telemetry
                  Could add external receiver on the FC board
                  Built-in Betaflight OSD(SPI Control)
                  Built-in Current meter Max 70A
                  Current meter scale set to 470
                  Built-in 5V 1A BEC
                  Built-in voltage detection
                  Onboard 4in1 ESC MCU upgraded to EFM8BB21
                  Power supply: 2-4S LiPo/LiPo HV (7v/17v)
                  Current: 10A continuous peak 12A (5 seconds)
                  Support BLHeliSuite programmable
                  Factory firmware: F_H_40_REV16_5.HEX
                  Default protocol: DSHOT600
                  Frsky NON-EU receiver Version SPI BUS receiver Frsky D8 compatible
                  Compatible Non EU transmitter D8 model
                  Channels: 8ch
                  Failsafe support
                  No ground interference ( Transmitter and receiver 1 m from the ground): 300m
                  VTX Output power: 25~200mw switchable
                  Frequency: 40CH
                  Input voltage: 3.3V 5.5V
                  Current consumption: 300mA(type)
                  Antenna: RG178 antenna
                  Frequency: 5.8GHz 5bands 40 channels
                  With Race band 
                  Smartaudio ready
                  Weight: 3g
                  Runcam NANO2 version Model: Nano 2
                  Image Sensor: 1/3" CMOS
                  Horizontal Resolution: 700TVL
                  Lens: 2.1mm(M8) FOV 155°
                  Signal System: NTSC / PAL
                  S/N Ratio: >50dB
                  Electronic Shutter Speed: Auto
                  Auto Gain Control (AGC): Auto
                  Min. Illumination: 0.01Lux@1.2F
                  D-WDR: Auto
                  Day/Night: Color
                  Power: DC 3-5.5V
                  Current : 110mA@5V 120mA@3.3V
                  Housing Material: ABS
                  Net Weight: 3.2g
                  Dimensions: L14mm*W14mm*H16mm
                  Caddx Baby turtle version TV system: NTSC/PAL changeable
                  Video Resolution: 1080P@60fps / 1080P@30fps / 720@60fps
                  Power Input: DC 4.5-20V
                  Mini Illumination: 0.01lux
                  Image Resolution: 2 Megapixels
                  Working Current: 380mA@5V/160mA@12V (low consumption)
                  OSD Menu: Yes (Support Voltage Display)
                  Video Files: MP4
                  Audio: Support
                  Electronic Shutter : PAL : 1/50-100,000 NTSC : 1/60-100,100
                  S/N Ratio: >60dB (AGC OFF)
                  Video Output: CVBS
                  Max Micro SD Card Supported: 8-64GB(need Class 10 or above, recommend Class 10/UHS-I/UHS-II)

                  How to add Flysky or DSM2/DSMX receiver for Crazybee V3.0 _Both version available? Click Here.

                  Package includes:
                  1 x Twig 115 2.5mm Frame
                  1 x Crazybee F4FR V3.0 PRO FC built-in Frsky NON-EU RX
                  4 x 1105 KV5200 Motor
                  1 x Gemfan 3025 3 Inch Propeller(4cw+4ccw)  
                  1 x Camera option1 : Runcam Nano2  / Camera option2:  CADDX Baby turtle
                  1 x 5.8g 25mw~200mw Switchable VTX
                  1 x Propeller Disassemble Tool
                  1 x Screwdriver

                  Leave a Comment