Price:
US$105.99

Free Shipping

Buy Now
Skystars Tiny Frog 75X 75mm 2S Whoop FPV Racing Drone BNF AIO CrazyFrog FC OSD w/SPI Frsky Receiver 1-2S 5A ESC Runcam Nano2 Camera

Compatibility

To confirm that this part fits your vehicle, please enter your vehicle's details below.

  • Year:

    Select

    • Make:

      Select

      • Model:

        Select

        • Submodel:

          Select

          • Trim:

            Select

            • Engine:

              Select

              • Clear All
              This part is compatible with 0 vehicle(s).
              Show all compatible vehicles
              This part is compatible with 1 vehicle(s) matching
              This part is not compatible with
              Recent searches

                • Year
                • Make
                • Model
                • Submodel
                • Trim
                • Engine

                  Skystars Tiny Frog 75X 75mm 2S Whoop FPV Racing Drone BNF AIO CrazyFrog FC OSD w/SPI Frsky Receiver 1-2S 5A ESC Runcam Nano2 Camera

                  This AIO F4 FC is suitable for a lighter 2S whoop drone, like 65X,75X etc. It integrated a Betaflight F411 processor FC, Betaflight OSD, SPI Frsky receiver and 1-2S 5A ESC. So the 2S drone could save many weight for a faster fly experience.

                  Specification:
                  Brand name: SKYSTARS
                  Item name: TinyFrog 75X 2019 FPV freestyle Racing Drone BNF
                  Wheelbase: 75mm 
                  Input voltage: 2S

                  AIO CRAZYFROG F4 TinyFrog 2S Flight Controller w/ 5A ESC & Compatible Frsky SPI Receiver 
                  Camera: Runcam Nano2 Camera
                  VTX: Skystars 25-100MW 5V Version
                  ESC: SKYSTARS 15A Blheli_S ESC 2-4S
                  Motor: Skystars ST1103 11000KV
                  Propeller: Gemfan 40mm
                  Battery: 300MAH 35c 2S 

                  Specification  
                  CRAZYFROG F4 TinyFrog 2S Flight Controller
                  CPU: STM32F411CEU6 (100MHZ )
                  Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
                  Size: 26mm x 26mm, fully compatible with the all whoop drone mounting pattern, recommend the TinyFrog75X frame.
                  Firmware version: betaflight_matekf411rx_4.0.0 (Development Version)
                  OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
                  Built in SPI Frsky D16 protocol native receiver, compatible with almost ALL Frsky FCC radios(e.g. Taranis X9D/X9D Plus/X7) or Frsky compatible transmitter module. Not compatible with Frsky LBT protocol.
                  Power Cable: 50mm, with AMASS XT30 connector
                  Weight: 4.5g 
                  DIAGRAM FOR F4 2S AIO FC (BUILT-IN FRSKY RX)
                  5A ESC
                  Built-in ESC with 5A continuous and peak 6A current
                  Power supply: 1-2S
                  Support BLHeliSuite programmable
                  Factory firmware: S_H_50_REV16_7.HEX
                  Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
                  Status LED
                  There are 3 LEDs on the bottom of the board to indicate the status, including Receiver LED ( Green), FC Status LED ( Red ) and FC Power LED ( Blue ). 
                  Frsky SPI  Receiver
                  Currently the built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules. Pay attention, this is a SPI connection receiver. In Betaflight Configuration, it should be setted as FRSKY_D receiver (aka Frsky D8 mode) or FRSKY_X receiver (aka Frsky D16 mode) in SPI RX mode.
                   
                  The Frsky D16 unstable connection issue is totally resolved since Betaflight 3.4.1. Nowadays, the default configuration from factory is Frsky D16 mode (FRSKY_X).
                   
                  Note: If you are using EU-LBT firmware radio controller, you might find that you can't bind successfully to this SPI Frsky receiver. Here are the solutions we provide for you.
                   
                  Binding Procedure
                  The binding procedure is reversed as usual. No need to click the bind button when power on.
                   
                  Power on the board, either by connecting the battery or USB power. Then the green receiver LED start to flash.
                  The second step, click the bind button for 3s. Then the green receiver LED will be solid on. This means that the receiver is in bind mode and you could start to bind your radio transmitter.
                  For detail procedure of binding, please check the SPI Frsky Receiver Binding Manual.
                  Runcam Nano2 Camera Image Sensor: 1/3" CMOS
                  Horizontal Resolution: 700TVL
                  Lens: 2.1mm(M8) FOV 155°
                  Signal System: NTSC / PAL
                  S/N Ratio: >50dB
                  Electronic Shutter Speed: Auto
                  Auto Gain Control (AGC): Auto
                  Min. Illumination: 0.01Lux@1.2F
                  D-WDR: Auto
                  Day/Night: Color
                  Power: DC 3-5.5V
                  Current: 110mA@5V
                  Housing Material: ABS
                  Net Weight: 3.2g
                  Dimensions: L14mm*W14mm*H16mm

                  Package Included:

                  1 x TinyFrog 75X 2019 AIO 1-2S SPI Frisky receiver FPV freestyle Racing Drone
                  1 x 300MAH 35c 2S battery

                  Leave a Comment