Price:
US$83.99

Free Shipping

TF3.2 LCD Display Screen + MKS GEN V1.4 Mainboard Motherboard +MOS MINI + 5x A4988 Driver + 6x Limit Switch Kit For 3D Printer

Compatibility

To confirm that this part fits your vehicle, please enter your vehicle's details below.

  • Year:

    Select

    • Make:

      Select

      • Model:

        Select

        • Submodel:

          Select

          • Trim:

            Select

            • Engine:

              Select

              • Clear All
              This part is compatible with 0 vehicle(s).
              Show all compatible vehicles
              This part is compatible with 1 vehicle(s) matching
              This part is not compatible with
              Recent searches

                • Year
                • Make
                • Model
                • Submodel
                • Trim
                • Engine

                  Package Included:

                  1 x MKS GEN V1.4 Motherboard
                  1 x MKS TFT32 display
                  6 x limit switch
                  6 x Switch link line
                  1 x MOS MINI
                  2 x 80cm power cord
                  5 x A4988 drive(red / green random)
                  5 x Heat sink
                  1 xUSB cable

                  About MKS GEN V1.4 Motherboard:



                  1. The 2560 and ramps 1.4 are assembled on a single board, which solves the problem that the Ramps 1.4 combination interface is cumbersome and prone to failure.

                  2, can replace the motor drive, support 4988 drive and 8825 drive, TMC2100 drive

                  3, the circuit board uses a high-quality 4-layer board, and specifically optimized thermal processing; Ramps is a 2-layer board.

                  4, using high-quality MOSFET tube, better heat dissipation.

                  5, using a dedicated power chip, support 12V-24V power input, to solve the problem of Ramps voltage conversion chip fever.

                  6, can accept 24V input, the same system power can reduce the thermal bed current to 1/4, effectively solve the hot bed MOS tube heating problem.

                  7, firmware can use open source firmware Marlin, configuration and ramps1.4 exactly the same, can directly replace Ramps1.4.

                  8, can directly connect Ramps1.4, 2004LCD control board and 12864LCD control board.

                  9, reserve motor pulse and direction output port, convenient external current to connect large current (such as 2A, 5A) motor drive circuit.

                  10. Reserve the Servos, AUX-1, and AUX-2 interfaces on Ramps 1.4, and provide three 5V outputs and three 12V output interfaces.
                  TF3.2 LCD Display Screen + MKS GEN V1.4 Mainboard Motherboard +MOS MINI + 5x A4988 Driver + 6x Limit Switch Kit For 3D Printer

                  About MKS TFT32 display:

                  1. Compatible with Marlin/Smoothieware/Repetier firmware
                  2. Appearance size: 110mmX65mm
                  3. Hole size: 102mmX57mm
                  4. Color touch screen: 3.2 inch touch screen
                  5. Microprocessor: 32-bit STM32 processor
                  6. Update method: SD file update
                  7. Support storage system: SD card, U disk
                  8. Support file format: Gcode
                  9. Extensible module (not included in the shipment):
                  10. WIFI module, after the shutdown module,
                  11. Breaking inspection switch, power failure, external card slot

                  About the limit switch:

                  1. Tap the travel limit switch
                  2. Normally open mechanical limit switch, compact size, easy to install, with trigger indicator. Plug and play.
                  MKS GEN L Mainboard + Mini MOS Modul + LCD 12864 Display + 6st Limit Swich + 5stk A4988 Driver Kit 3D Printer Parts
                   

                  About the MOS MINI Module:

                   0. This is a 3d printer hot bed high power expansion module
                   1. The heat dissipation is more powerful, solving the problem of excessive power and current load due to the hot bed.
                   2. Excellent performance MOS tube (nominal maximum current 280A).
                   3. Large heat sink, the maximum current can be up to 30A. Do not exceed 30A during use.
                   4. You can directly use the hot bed output signal control of Ramp1.4 and MKS series motherboards.
                   5. Can use 5-24v digital signal control

                  MKS GEN L Mainboard + Mini MOS Modul + LCD 12864 Display + 6st Limit Swich + 5stk A4988 Driver Kit 3D Printer Parts


                  Leave a Comment