Price:
US$107.99

Free Shipping

Einsy Rambo 1.1a Mainboard + 2004 LCD Display For Prusa i3 MK3 With 4 Trinamic TMC2130 Control 4 Mosfet Switched Outputs 3D Printer Part

Compatibility

To confirm that this part fits your vehicle, please enter your vehicle's details below.

  • Year:

    Select

    • Make:

      Select

      • Model:

        Select

        • Submodel:

          Select

          • Trim:

            Select

            • Engine:

              Select

              • Clear All
              This part is compatible with 0 vehicle(s).
              Show all compatible vehicles
              This part is compatible with 1 vehicle(s) matching
              This part is not compatible with
              Recent searches

                • Year
                • Make
                • Model
                • Submodel
                • Trim
                • Engine

                  Features:
                   
                  Logic
                   
                  For Arduino MEGA compatible Atmega2560 and Atmega32u2 processors are compatible with all RAMPS class firmware
                  Crystals for both usb and mcu (timing accurate to 10ppm)
                  3 Thermistor jacks + 4th Thermistor circuit on ZProbe.
                   
                  Motor Drivers
                   
                  4 Trinamic TMC2130 1/256th microstep motor drivers(2 connectors on Z for Prusa Mendel and other dual Z printer designs)
                  SPI Control of stepper current instead of PWM.
                  Microstep mode configured by MCU through firmware (SPI, no jumpers needed)
                  PWM DC outputs (Extruders, Fans, Etc.)
                   
                  4 outputs (1 Extruder, 1 BED, 2 low power (fan,etc)
                   
                  Low resistance mosfets for cool running
                  Indicator led for each channel
                  FANS have 3pin fan connector.
                  FANS have 5V instead of 12-24V power source.
                  FAN connectors have tachometer feedback pin to the MCU to measure fan speed in capable firmware.
                   
                  Power
                   
                  2 power input rails
                  Heated Bed, 15A 12-24V (15A dedicated fuse)
                  Primary Power 10A 12-24V: Motors, Logic & Fans (5A dedicated fuse) + Extruder (5A dedicated fuse)
                  Built in SMPS for 5V generation from the Motors, Logic & Fans rail
                  Provides 5V power to FANS
                   
                  Connectors
                   
                  4-pin motor,zprobe plug – Molex 5057-9404
                  3-pin fan plug – Molex 5057-9403
                  2-pin thermistor, mech. endstop plug – Molex 5057-9402

                   
                  2004LCD Display
                   
                  Brand new and high quality.
                  This smart controller contains a SD-Card reader, an rotary encoder and a 20 character x 4 line LCD display. You can easy connect it to your Ramps board using the "smart adapter" included.
                  After connecting this panel to your Ramps you don't need your pc any more, the smart controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the smart controller
                  Print your 3D designs without PC, just with a g-code design stored on the SD card.
                  Firmware: You need Marlin firmware v3 or newer. If you are using older firmware, you must re-flash your board.
                  Size: 15cm x 5.8cm

                   
                  Package Included:
                   
                  1x EinsyRambo 1.1a Mainboard
                  1x 2004 LCD Display
                  1x Adapter Module
                  5x black heat sink
                  1x USB Cable
                  1x Pin Cable
                   
                   










                  Leave a Comment