Free Shipping

RF Nano V3.0 Micro USB Module ATmega328P QFN32 5V 16M CH340 Integrate NRF24l01+2.4G Wireless Imme For Arduino


To confirm that this part fits your vehicle, please enter your vehicle's details below.

  • Year:


    • Make:


      • Model:


        • Submodel:


          • Trim:


            • Engine:


              • Clear All
              This part is compatible with 0 vehicle(s).
              Show all compatible vehicles
              This part is compatible with 1 vehicle(s) matching
              This part is not compatible with
              Recent searches

                • Year
                • Make
                • Model
                • Submodel
                • Trim
                • Engine

                  1. Creative products, RF-Nano-Board: Upgraded nano board for Arduino, The main chip is ATMEGA328P-MU QFN32, the latest bootloader (Arduino IDE 1.8.8) was burned down. It is fully compatible with the common nano board. RF-Nano-Board is PIN-PIN with Arduino Nano V3.0,and share the same codes.
                  2. More convenient for application: The RF-Nano-Board integrates an NRF24L01+ module with Arduino nano v3.0 board, which is very convenient for 2.4G wireless connect application.
                  3. High quality material and Technology: We used high quality PCB original material and Immersion Gold Technology to make sure every board has smooth edge and more reliable.
                  4. Super small volume design, more convenient to use: The PCB size is only 48mm*19mm, the pin is fully compatible with Nano V3.0,No Soldering needed. The micro usb port is more convenient to use.
                  5. RF-Nano-Board using CH340 chip to UART, you can download mac, windows, Linux three system drivers.
                  Microcontroller ATmega328P
                  Nrf24L01+ 2.4G wireless
                  Architecture AVR
                  Operating Voltage: 5 V
                  Flash Memory: 32 KB of which 2 KB used by bootloader
                  SRAM: 2 KB
                  Clock Speed: 16 MHz
                  Analog I/O Pins: 8
                  EEPROM: 1 KB
                  DC Current per I/O Pins: 40 mA (I/O Pins)
                  Input Voltage: 7-12 V
                  Digital I/O Pins: 22
                  PWM Output: 6
                  Power Consumption: 19 mA
                  Weight: 9g

                  ◆ It is fully compatible with the Arduino nano-v3.0 pin and its usage method
                  ◆ BLE chip: TI CC2540
                  ◆ Work channel: 2.4G
                  ◆ Transmission distance: 50m
                  ◆ Supports AT directive to configure BLE
                  ◆ Support USB virtual serial port, hardware serial port, BLE three-way transparent transmission
                  ◆ Support master and slave switch
                  ◆ Supports sending over 20byte.
                  ◆ Supports iBeacons
                  ◆ Interface: Micro-USB
                  ◆ Input voltage: USB power supply, Vin6~12V, 5V
                  ◆ MCU: ATmega328P-MU QFN32
                  ◆ Bootloader: Newest Arduino1.8.8
                  ◆ Pin: Two Lines 2.54mm-15Pin
                  ◆ Size: 48mm x 19mm x 12mm
                  Package includes: 
                  1 x RF Nano board

                  Please use Arduino IDE 1.8.6 or higher version, First, install the CH340 driver, then follow this selection path in Arduino IDE: Tools –  Board“Arduino Nano” Processor “ATmega328P",

                  otherwise you'll find that you can't burn any program. 

                  Leave a Comment