Price:
US$119.99

Free Shipping

Buy Now
SKYSTARS STX225 DIY Version 225mm RC FPV Racing Drone PNP w/ F4 OSD 35A RGB LED 1200TVL 40CH 600mW VTX

Compatibility

To confirm that this part fits your vehicle, please enter your vehicle's details below.

  • Year:

    Select

    • Make:

      Select

      • Model:

        Select

        • Submodel:

          Select

          • Trim:

            Select

            • Engine:

              Select

              • Clear All
              This part is compatible with 0 vehicle(s).
              Show all compatible vehicles
              This part is compatible with 1 vehicle(s) matching
              This part is not compatible with
              Recent searches

                • Year
                • Make
                • Model
                • Submodel
                • Trim
                • Engine

                  SKYSTARS STX225 DIY Version 225mm RC FPV Racing Drone PNP w/ F4 OSD 35A RGB LED 1200TVL 40CH 600mW VTX

                   
                  Notice: this is the DIY version that comes unassembled.

                  Specification: 
                  Brand name: SKYSTARS 
                  Item name: STX225 DIY version FPV racing drone PNP
                  Recommended 3-5S battery (package not included)

                   
                  Frame kit Wheel base: 225mm
                  Frame arm thickness: 4mm
                  Bottom plate thickness: 2mm
                  Side plate thickness: 2mm
                  Frame kit material: 3K carbon fiber 
                  2204 2300KV Brushless Motor Motor KV: 2300RPM/V 
                  Idle current (Io/10V): 1.26A
                  Lipo cell: 3-5S
                  Weight: 26g
                  Max continuous current: 25A
                  Max continuous power: 240W
                  Max thrust: 700g (4S/5")
                  Configu-ration: 12N/14P
                  Motor resistance (RM): 0.0572 Ω 
                  Stator diameter: 22mm
                  Stator thickness: 4mm
                  Motor diameter: 27.55mm
                  Motor body length: 20mm
                  Overall shaft length: 34.2mm
                  Prop adapter shaft: M5
                  Bolt holes spacing: 16mm
                  Bolt thread: M3
                  Propeller: 5inch
                  35A BLHeli_32  RGB LED ESC Continuous current: 35A
                  Peak Current: 40A(10S)
                  Input voltage: 2-5S
                  BEC: NO bec
                  Main control chip: STM32F051
                  Firmware: BLHeli_32 supports 500HZ PWM, Oneshot125, Oneshot42, Multishot, Dshot150/300/600/1200.
                  Customized F4 Flight Controller Main control chip: STM32F405
                  Sensor:MPU6000
                  Power supply: 5V
                  Integrated OSD
                  Onboard LC filter
                  PID cycle rate & gyro refresh rate up to 8Khz
                  Supports BetaFlight / inva racing firmware
                  1200TVL CMOS Camera Case size: 19mm*19mm
                  Weight: 9.5g
                  Total pixels: PAL: 1020H×596V (0.61MP); NTSC: 1020H×508V (0.52MP)
                  Effective pixels: PAL: 976H×582V (0.57MP); NTSC: 976H×494V (0.48MP)
                  Signal system: PAL/NTSC switchable
                  Resolution ratio(horizontal center): 1200TVL
                  Video output: 1.0Vp-p/75Ω
                  Automatic gain control: yes
                  White balance: on/off optional 
                  Exposure mode: electron exposure
                  Electronic shutter: 1/50(1/60) – 1/100000 S
                  Gamma correction: 0.45/1.0
                  Synchronization method: inter-sync
                  Camera lens: standard 2.3mm
                  Lens operating voltage: DC12V (wide voltage, measured can work normally at 7.5-13V)
                  Working current: 70mA (low power consumption)
                  Working temperature: -20℃~-60℃
                  Humidity: 0%~98% 
                         5.8G 40CH 600mw switchable VTX                    Output power & transmission distance: ≥0.5km@25mW, ≥1km@200mW, ≥2km@600mW
                  Transmitting power: 600mW
                  Full video format: NTSC /PAL
                  Input voltage & power dissipation: 7V~24V, +12V/190mA
                  Size: 38*18*8mm
                  Weight: ≤16g(except antenna)
                  With output power self-check function.
                  Nixie tube SCAN: frequency point (1-8), frequency band (A-E), power (1-3, 0=0mw, 1=25mw, 2=200mw, 3=600mw)
                  Antenna: RP-SMA
                  5042 3 Blade Propeller Material: PC
                  Mounting hole: 5mm
                  Center thickness: 8mm
                  Quantity: 2 pairs
                  Weight: 7.25G a pair   
                  Color: blue, red, yellow, purple, white MIX
                  Delivery color randomly 

                  Package included:
                  1x STX225 DIY version FPV racing drone PNP









                  Leave a Comment